CNC Robot Parts
Robot Actuator Cylinder Housing 7075-T6 Aluminum Honed Bore Hard Anodized 0.005mm Roundness
Custom robot actuator cylinder housing machined from 7075-T6 bar, with the bore and end faces finished in one clamping, honed to 0.005 mm roundness at Ra 0.2, then hard anodized 50um and re-honed for seal fit. Every shell is pressure tested to 0.6 MPa with results per serial. Non-standard shells accepted from one piece under mutual NDA, with 3-7 day prototypes and repeatable series supply from an ISO 9001:2015 plant established in 2008.
Robot Shoulder Yoke Fork Connector 2024-T351 Aluminum Bushed Pin Bores 0.008mm Symmetry
Custom robot shoulder yoke fork connector machined from 2024-T351 plate. Both fork arms finished in one clamping and pin bores bored in a single cycle to 0.008 mm coaxiality, with replaceable bushings graded and pressed on a recorded force log. Non-standard forks accepted from one piece under mutual NDA, with 3-7 day prototypes and repeatable spares from a frozen programme.
Robot Joint Connecting Arm Dual Bearing Housing 6082-T6 Aluminum Press Fit Select 0.008mm
Custom robot joint connecting arm with dual bearing housings, machined from 6082-T6 plate. Both seats bored in one clamping to 0.008 mm coaxiality, bore band held to 0.005 mm and graded A/B, with seal grooves, grease passages and a recorded bearing press trial. Non-standard arms accepted from one piece under mutual NDA, with 3-7 day prototypes and repeatable spares from a frozen programme.
Robot Arm Linkage Set 6061-T6 Aluminum Mirrored Pair Weight Matched 0.005mm Bore Coaxial
Custom robot arm linkage set machined as a mirrored pair from one 6061-T6 plate. Both ends bored in a single setup for 0.005 mm coaxiality, arms weight matched within 1 g and serialised as a set. Non-standard links accepted from one pair under mutual NDA, with 5-10 day first sets and repeatable spares from a frozen programme.
Robot Tooling Fixture Set 6061 Aluminum Locating Blocks Clamps Ground 0.01mm Hole Pitch
Custom robot tooling and fixture sets machined as one project: locating blocks, clamp straps, support posts, base rails and dowel bushings sharing a single datum scheme. Hole pitch 0.01 mm, ground faces flat to 0.005 mm, every component laser serialised to its set. Non-standard assemblies accepted from one set under mutual NDA, with 5-10 day first sets and repeatable spare parts from a frozen programme.
Hollow Robot Joint Housing 6061-T6 Seamless Tube Through Bore Cable Routing 0.01mm Coaxial
Custom hollow robot joint housing machined from 6061-T6 seamless tube, with a through bore used as an internal cable route. Twin flanges held coaxial to 0.01 mm, wall scanned to plus or minus 0.1 mm and bore finished to Ra 1.6. Non-standard drawings accepted from one piece under mutual NDA, with 3-7 day prototypes and staged series delivery from an ISO 9001:2015 plant established in 2008.
Robot Base Plate MIC-6 Cast Aluminum Double-Sided Machined 0.01mm Flatness Dowel Datum
Custom robot base plate machined from MIC-6 cast aluminum tooling plate on both faces. Flatness 0.01 mm over the full face with a mapped CMM report, dowel holes honed to H7 at 0.012 mm position. Non-standard drawings accepted from one piece under mutual NDA, with 3-7 day prototypes and staged batch delivery from an ISO 9001:2015 plant established in 2008.
Robot Gearbox Housing 7075-T6 Aluminum Matched Cover Pair Line Bored H7 Bearing Seats 0.005mm
Custom 7075-T6 aluminum robot gearbox housing, machined as a matched body and cover pair from one plate and line bored after bolting. Bearing seats to H7, gear centre distance held to 0.005 mm, assembled-state CMM report with every batch. Non-standard drawings accepted from one piece under mutual NDA, with 3-7 day prototypes and staged series delivery from an ISO 9001:2015 plant established in 2008.
Robot Joint Housing 6061 Aluminum Helical Weight Slots Turn-Mill Machined 0.006mm Concentricity
Custom 6061 aluminum robot joint housing turned and milled in one clamping. Helical weight-reduction slots, H7 bearing seat and 0.006 mm bore-to-flange concentricity, verified on CMM with a first article report. Non-standard drawings accepted from a single piece under mutual NDA, with 3-7 day prototypes and staged batch delivery from an ISO 9001:2015 plant established in 2008.
